|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
LAB TOP VIEW SCR TRIGGER REMOTE ACTIVATE RESET O.V. INDICATE O.V. DELAY O.V. INPUT U.V. INPUT U.V. DELAY 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 SEME IP1543 SERIES V IN VR E F GND C.L. OUTPUT OFFSET/COMP C.L. NON-INV. INPUT C.L. INV. INPUT U.V. INDICATE POWER SUPPLY SUPERVISORY CIRCUIT FEATURES * 4.5 to 40V operation over full temperature range * Reference voltage trimmed to 1% accuracy * Includes over-voltage, under-voltage and current sensing * Programmable time delays * SCR "Crowbar" drive of 300mA * Remote activation capability * Optional over-voltage latch capability J Package - 16 Pin Ceramic DIP N Package - 16 Pin Plastic DIP D Package - 16 Pin Plastic (300) SOIC Order Information Part J-Pack N-Pack D-16 Temp. Number 16 Pin 16 Pin 16 Pin Range IP1543 -55 to +125C IP3543 0 to +70C Note: To order, add the package identifier to the part number. eg. IP1543J IP3543D-16 ABSOLUTE MAXIMUM RATINGS (Tcase = 25C unless otherwise stated) +VIN Input Supply Voltage Sense Inputs SCR Trigger Current Indicator Output Voltage Indicator Output Sink Current PD PD TJ TSTG TL Power Dissipation Power Dissipation TA = 25C Derate @ TA > 50C TC = 25C Derate @ TC > 25C 40V VIN Internally Limited +40V 50mA 1W 10mW/C 2W 16mW/C See Ordering Information -65 to +150C (soldering, 10 seconds) +300C Prelim. 1/96 Operating Junction Temperature Storage Temperature Range Lead Temperature Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. LAB DESCRIPTION The IP1543 and IP3543 power supply supervisory circuits contain all the functions necessary to monitor and control the output of a sophisticated power supply system. Included on the chip are over-voltage (O.V.) sensing with externally programmable delay used to trigger an external SCR "Crowbar", under-voltage (U.V.) sensing with externally programmable delay used to sense either the power supply output or the line input voltage, a third op-amp/comparator with provision for external compensation and/or offset programming used for either current limiting or as an additional voltage monitor, and a voltage reference trimmed to 1%. SEME IP1543 SERIES BLOCK DIAGRAM VIN 250 A 9 7 U.V. INDICATE U.V. SENSE U.V. 8 U.V. DELAY VREF V IN 15 16 2.5 V REF. GND O.V. SENSE 14 250 A 6 O.V. VIN 5 1 SCR TRIGGER O.V. INDICATE O.V. DELAY C.L. INV. C.L. NON-INV. 10 11 13 C.L. OUTPUT 4 C.L. 12 2 3 OFFSET / COMP REMOTE ACTIVATE RESET RECOMMENDED OPERATING CONDITIONS VIN Input Supply Voltage Input Voltage Range Reference Load Current Indicate Output Current Operating Ambient Temperature Range IP1543 IP3543 +4.5 to +40V 0 to VIN - 3 0 to 10mA 0 to 10mA -55 to +125C 0 to +70C Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 1/96 LAB ELECTRICAL CHARACTERISTICS (TJ = Over Operating Temperature Range unless otherwise stated) Parameter Input Voltage Range Supply Current SEME IP1543 SERIES Test Conditions VIN = 40V Min. 4.5 IP1543 Typ. Max. 40 7 10 Min. 4.5 IP3543 Typ. Max. 40 7 10 Units V mA REFERENCE SECTION Output Voltage Line Regulation Load Regulation Short Circuit Current Temperature Stability TJ = 25C VIN = 4.5 to 30V IREF = 0 to 10mA VREF = 0 12 2.48 2.45 1 1 25 50 2.5 2.52 2.55 5 10 40 12 2.45 2.4 1 1 25 50 2.5 2.55 2.6 5 10 40 V mV mA ppm/C SCR TRIGGER SECTION Peak Output Current Peak Output Voltage Output Off Voltage Remote Activate Current Remote Activate Voltage Reset Current Reset Voltage Output Current Rise Time Prop. Delay from Pin 2 Prop. Delay from Pin 6 VIN = 5V VO = 0 VIN = 15V VIN = 40V Pin 2 = Gnd Pin 2 = Open Pin 3 = Gnd Pin 3 = Open RL = 50 CD = 0 VPIN2 = 0.4V VPIN6 = 2.7V TJ = 25C TJ = 25C 2.45 2.4 TJ = 25C Sense Input = 0V 25 -0.3 0.2 6 VD = 0 200 250 -1 0.5 8 300 200 Pin 2 = Gnd Pin 2 = Gnd TJ = 25C IO = 100mA RG = 0 100 12 200 13 0 -0.1 1.5 -0.1 1.5 400 300 500 0.1 -0.8 6 -0.8 6 400 100 12 200 13 0 -0.1 1.5 -0.1 1.5 400 300 500 0.1 -0.8 6 -0.8 6 400 mA V mA V mA V mA/s ns ns COMPARATOR SECTIONS Input Threshold (Input Voltage TJ = 25C Rising on Pin 6, Falling on Pin 7) 2.5 2.55 2.6 2.4 2.35 2.5 2.6 2.65 V mV Input Hysteresis Input Bias Current Delay Saturation Delay High Level Delay Charging Current 25 -0.3 0.2 6 250 -1 0.5 8 300 A V A Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 1/96 LAB ELECTRICAL CHARACTERISTICS (TJ = Over Operating Temperature Range unless otherwise stated) Parameter Indicate Saturation Indicate Leakage SEME IP1543 SERIES Test Conditions Min. IP1543 Typ. Max. 0.2 0.01 0.5 1 Min. IP3543 Typ. Max. 0.2 0.01 400 0.5 1 Units V A ns COMPARATOR SECTIONS (cont.) IL = -10mA VIND = 40V VPIN6 = 2.7V Propagation Display CD = 0 VPIN6 = 2.7V CD = 0 Input Voltage Range Input Bias Current Input Offset Voltage CMRR AVOL Output Saturation Output Leakage Small Signal Bandwidth Propagation Delay Pin 12 = Open Pin 12 = Open VCM = 0 VCM = 0 70 60 72 VIN = 15V VCM = 0 VPIN7 = 2.3V TJ = 25C VPIN7 = 2.3V TJ = 25C 0 -0.3 0 100 70 80 0.2 0.01 TJ = 25C TJ = 25C 5 200 0.5 1 400 10 10 ms CURRENT LIMIT SECTION VIN - 3 -1 10 130 70 60 72 0 -0.3 0 100 70 80 0.2 0.01 5 200 0.5 1 VIN - 3 -1 15 130 V A mV 10k from Pin 12 to Gnd VCM = 0 to 12V Pin 12 = Open IL = -10mA VIND = 40V AV = 0dB Voverdrive = 100mV dB V A MHz ns NOTES 1. Test Conditions unless otherwise stated: VIN = 10V for IP1543 TJ = -55 to +125C for IP3543 TJ = 0 to +70C Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 1/96 LAB APPLICATIONS INFORMATION Typical Application POWER SUPPLY R SC OUT OF TOLERANCE INDICATORS SEME IP1543 SERIES Current Limit VTH 1000 16 2.5V REF. 14 13 10 15 R4 7 9 4 R1 TO VOLTAGE CONTROL LOOP U.V. TO SYSTEM CONTROL SCR "CROWBAR" RG 1 3 CS is determined by the current loop dynamics. Peak Current to load IP VTH + VO RSC RSC R2 R2 + R3 R5 + R6 R6 R2 R5 6 SCR TRIGGER Low Output Voltage Limit VO(low) = 2.5 (R4 + R5 + R6) High Output Voltage Limit VO(high) = 2.5 (R4 + R5 + R6) Voltage Sensing Delay TD = 10000 CD C.L. 12 11 O.V. 2 5 8 LATCH RESET R1 CS R3 R6 C D1 C D2 SCR trigger power limiting resistor RG > VIN -5 0.2 Sensing Multiple Supply Voltages BIAS SUPPLY MAIN POSITIVE SUPPLY R1 7 TO 339 COMPARATORS 16 IP1543 U.V. R2 2.5V REF. SCR TRIGGER 1 TO SHUTDOWN CIRCUIT 6 O.V. R3 GROUND ADDITIONAL POSITIVE SUPPLY NEGATIVE SUPPLY VOLTAGE R4 R5 R6 R7 14 15 4 9 2 3 339 QUAD COMP. MASTER POWER SUPPLY CONDITION INDICATOR Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 1/96 LAB Input Line Monitor IP1543 15 2.5V REF. 9 7 SEME IP1543 SERIES U.V. R2 LINE INPUT 8 14 Overcurrent Shutdown MAIN SUPPLY BUS BIAS VOLTAGE IP1543 16 SCR "CROWBAR" SCR TRIGGER 2.5V REF. C.L. 1 RG 14 15 11 10 12 13 2 3 R1 CD R2 SUPPLY BUS RETURN R SC Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 1/96 LAB TYPICAL PERFORMANCE CHARACTERISTICS Comparator Input Hysteresis Comparator Input Hysteresis SEME IP1543 SERIES SCR Trigger Power Limiting Current Limit Amplifier Gain Current Limit Amplifier Frequency Response Activation Delay vs Capacitor Value Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 1/96 |
Price & Availability of IP1543 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |